Why aren’t my clothes getting cleaned properly in the washer?

This is often caused by incorrect cycle or temperature settings, an overloaded drum, a partially blocked filter, or using too little (or the wrong type of) detergent.

What causes a washing machine to leak water?

Common causes include a worn door boot on front-load washers, loose or cracked hoses, a faulty drain pump, or a damaged tub seal.

What does loud banging or grinding mean in a washer?

It can indicate worn drum bearings, a failing motor, loose components, or an unbalanced load hitting the cabinet during spin.

Why does my washer stop mid-cycle?

Possible reasons include a faulty door/lid switch, control board issues, drain problems, or power interruptions to the washer.

Why do clothes come out soaking wet after washing?

This is usually a spin issue caused by a failing motor, worn belt, a blocked drain pump, or an unbalanced load preventing full spin speed.

Why is my washer vibrating or walking during spin?

Common causes include worn shock absorbers or suspension rods, damaged motor mounts, or the washer not being level on the floor.

What should I check if my washer won’t start?

Check power and breakers first. If power is good, the issue may be the door lock, control board, user interface, or an internal fuse.

Why is my washer overfilling or overflowing?

This can be caused by a clogged pressure hose, faulty water level sensor, a stuck water inlet valve, or the control board not shutting the valve off.

Why isn’t my washer draining or rinsing properly?

A partially blocked drain pump, kinked/clogged drain hose, or too much detergent can leave clothes soapy and damp.

Why won’t my washer agitate?

This can point to a worn drive belt, failed motor, stripped agitator dogs (top-load washers), or transmission/gearcase problems.

Why does my dryer have poor airflow or take too long to dry?

Poor airflow is commonly caused by lint buildup in the venting system, a clogged lint screen, or crushed/blocked ducting. Restoring airflow improves drying time and helps prevent overheating.

What causes a dryer to stop heating?

A dryer may stop heating due to a failed heating element, thermostat, thermal cut-off fuse, or incorrect voltage supply. A proper diagnosis confirms which component is at fault.

Why does my dryer have no power or won’t turn on?

Common causes include a tripped breaker, blown thermal fuse, faulty outlet, or an internal electrical failure. Verify power first, then check safety components and controls.

Why won’t my dryer start even though it has power?

A dryer may have power but won’t start due to a faulty door switch, broken start switch, user interface failure, or control board issues.

What causes the dryer drum to stop turning?

A non-spinning drum is usually caused by a broken belt, seized drum rollers, a failed motor, or a worn idler pulley.

Why is my dryer overheating?

Overheating is often caused by restricted airflow (blocked venting) or a defective cycling thermostat. Continuing to run it can damage components and create a safety risk.

Why is my dryer loud or vibrating?

Noise and vibration can come from worn drum rollers, blower wheel problems, loose panels, or an unlevel dryer. Addressing it early can prevent larger failures.

Why are my clothes still damp after a full cycle?

Damp clothes are often caused by vent blockage, a clogged lint filter, weak heat, or a faulty moisture sensor. Airflow and heating performance should be checked together.

What causes burning or musty smells from a dryer?

Smells can be caused by lint near the heater, belt wear, or buildup on heating components. Stop using the dryer if you smell burning and have it inspected for safety.

Why won’t my dryer stop running?

A dryer that won’t stop may have a faulty cycling thermostat, defective timer, stuck relay, or moisture sensor problem that prevents the cycle from ending correctly.

Why won’t my gas cooktop burner light?

Common causes include a dirty igniter/electrode, clogged burner ports, a failed spark module, faulty ignition switch, or loose wiring. Cleaning and proper testing usually identifies the cause quickly.

Why is my cooktop burner heating unevenly?

Uneven heat is often caused by mis-seated burner caps (gas), partially blocked ports, or a failing element (electric). Using the correct cookware also matters, especially on induction.

Why does the cooktop have power but no heat?

On electric or induction cooktops, a failed element, surface control board, sensor issue, or power/connection problem can prevent heat even when the unit powers on.

What should I do if I smell gas near my cooktop?

Treat it as urgent: stop using the appliance, ventilate the area, and arrange an inspection. Gas odours can indicate a leak or incomplete combustion and should be addressed for safety.

Why do my burners shut off after ignition?

This can happen when flame sensing components are weak/dirty (thermocouple or flame sensor), gas flow is restricted, or ignition components are failing. The burner may light briefly then stop.

Why does my cooktop keep tripping the breaker?

Repeated breaker trips can indicate a shorted element, wiring fault, moisture intrusion, or control board failure. Stop using it and book service to prevent further damage.

Why won’t my dishwasher start?

A common cause is a faulty or misaligned door latch that prevents the unit from sensing a safe closed door.

What are the most common dishwasher leak points?

Leaks often come from worn door gaskets, loose/cracked hoses, sump area issues, or a failing water inlet valve.

Why is my dishwasher noisy?

Grinding or humming can indicate debris in the pump/impeller area, circulation pump wear, or a failing wash motor.

Why is water left in the bottom after a cycle?

This is usually caused by a clogged drain hose, blocked filters, a jammed drain pump, or a check valve problem.

How can I improve dishwasher drying?

Poor drying can be caused by a failing heating element/thermostat, a vent fan issue, or rinse-aid and loading factors. A service check can confirm the exact cause.

Why won’t my microwave start when I close the door?

A faulty or misaligned door switch/door latch system can stop operation for safety. It usually requires replacement or adjustment.

Why does my microwave run but not heat?

This can be caused by a failed magnetron, diode, capacitor, or high-voltage circuit issue. It should be diagnosed by a qualified technician.

What causes sparking inside a microwave?

Sparking is commonly caused by metal objects, heavy splatter/carbon buildup, or a damaged waveguide cover. Stop use and inspect/clean safely.

Why does my microwave keep tripping the breaker?

Breaker trips can be caused by internal shorts, failing high-voltage components, or outlet/circuit issues. Proper testing is needed.

Why is my over-the-range microwave overheating?

Blocked vents, dirty grease filters, tight cabinet clearances, or failed cooling fans can cause overheating and shutdowns.

Why won’t my gas stove burner ignite?

Common causes include a weak igniter, clogged burner ports/orifice from spills, failed spark module, or a problem with the gas valve or regulator. If you smell gas, stop using the appliance and have it inspected.

What causes an electric stove burner to stop heating?

A failed heating element, burned terminal block, damaged wiring, or a failed surface switch/control board can stop a burner from heating. A proper diagnosis confirms the exact part before ordering.

Why is my stove temperature inaccurate or cooking unevenly?

Inaccurate temperatures can be caused by a faulty thermostat/temperature sensor, calibration issues, heat loss from a worn door gasket, or airflow restrictions from heavy grease buildup.

What does it mean when the stove display is dead or shows an error code?

A dead display or error code often points to a control board, user interface, or power supply issue (including breakers/outlet). Diagnostics help confirm whether the issue is the board, wiring, or incoming voltage.

Why do I smell gas when using the stove?

Gas odors can be caused by incomplete combustion, a burner not seated correctly, a damaged gasket, or a leak in the gas line/valve/regulator area. Turn the appliance off, ventilate the space, and arrange a professional inspection.

When should I call a professional for stove repairs instead of DIY?

Call a professional for any gas smell, electrical burning smell, repeated breaker trips, sparking, control board faults, or wiring issues. These problems can be safety hazards and need proper testing and repair.

Why is my oven not heating properly?

Common causes include failed bake/broil elements, a faulty temperature sensor, wiring/connectors issues, or a control problem. Professional diagnosis helps confirm the root cause before ordering parts.

Why does my oven take a long time to preheat?

Slow preheat is often linked to a weakening heating element, inaccurate sensor/thermostat feedback, or heat loss from a worn door gasket or misaligned door.

My oven temperature is inconsistent. What usually causes that?

Temperature swings can be caused by sensor calibration problems, failing elements, airflow/heat loss issues from door sealing problems, or control/relay faults.

What should I do if I smell gas from my oven?

Turn the oven off, ventilate the area, avoid flames/sparks, and contact a gas-licensed professional immediately. Do not attempt DIY repairs when gas smell is present.

Why is my oven door not sealing?

A worn gasket, bent hinges, or door alignment issues can prevent a tight seal. A poor seal causes heat loss and uneven cooking and usually needs adjustment or replacement parts.

Can a bad control board cause an oven to stop working?

Yes. Error codes, dead displays, and unresponsive buttons can indicate a control board or user interface failure. Testing is recommended to confirm before replacement.

What temperature should my refrigerator and freezer be set to?

A common target is about 4°C (39°F) for the fridge and about -18°C (0°F) for the freezer. If you’re still seeing warm spots, there may be an airflow, fan, defrost, or sealed-system issue.

Why is my refrigerator running constantly?

Constant running is often caused by dirty condenser coils, worn door gaskets, blocked vents, a failing fan, or heavy frost from a defrost/drain problem. Fixing the root cause can reduce energy use and prevent compressor strain.

Why is water leaking from my refrigerator?

The most common cause is a blocked or frozen defrost drain. Leaks can also come from a cracked water line, loose fittings, or an ice maker fill issue—especially if the leak appears near the back or under the crisper.

Top 10 Common Appliance Issues & Possible Repairs

Edmonton · Calgary · Red Deer & Nearby Areas

10 Common Washer Problems We Fix Every Day

Having trouble with your washing machine? Here are the most common issues our technicians handle during a Washer Repair Service.

1

Clothes not getting cleaned properly

Often caused by incorrect cycle or temperature settings, an overloaded drum, a partially blocked filter, or using too little (or the wrong type of) detergent.
2

Washer leaking water

Common sources include worn door boot (front-loaders), loose or cracked hoses, a faulty drain pump, or a damaged tub seal.
3

Loud banging or grinding noises

Can indicate worn drum bearings, a failing motor, loose components, or an unbalanced load hitting the cabinet during spin.
4

Washer stops mid-cycle

May be related to a faulty door/lid switch, control board issues, drain problems, or power interruptions to the machine.
5

Clothes come out soaking wet

Usually a spin issue: failing motor, worn belt, blocked drain pump, or an unbalanced load preventing full spin speed.
6

Excessive vibration or “walking” washer

Often caused by worn shock absorbers or suspension rods, damaged motor mounts, or the washer not being level on the floor.
7

Washer won’t start

Check power and breakers first. If power is good, the issue may be with the door lock, control board, user interface, or an internal fuse.
8

Washer overfilling or overflowing

Can be due to a clogged pressure hose, faulty water level sensor, stuck water inlet valve, or control board not shutting the valve off.
9

Clothes not rinsing or draining properly

A partially blocked drain pump, kinked/clogged drain hose, or too much detergent can leave clothes soapy and damp.
10

Washer won’t agitate

Can point to a worn drive belt, failed motor, stripped agitator dogs (top-loaders), or transmission/gearcase problems.

If you’re seeing any of these issues, it’s usually cheaper to repair early before damage spreads to other parts.
Book Your Washer Repair with Advance Appliance Ltd

Edmonton · Calgary · Red Deer & Nearby Areas

10 Common Dryer Problems We Fix Daily

Here are the most frequent issues our certified technicians repair during a Dryer Repair Service.

1

Poor or No Airflow

Lint buildup in the vent, clogged lint trap, or crushed ducts reduce airflow and cause long drying times.
2

Dryer Not Heating

Often caused by a failed heating element, thermostat, cut-off fuse, or improper voltage supply.
3

No Power at All

Can be due to a tripped breaker, blown thermal fuse, faulty outlet, or internal electrical failure.
4

Dryer Won’t Start

Door switch issues, broken start switch, user interface failure, or control board malfunction.
5

Drum Not Turning

Usually a worn or broken belt, seized rollers, faulty motor, or damaged idler pulley.
6

Dryer Overheating

Caused by blocked vents, defective cycling thermostat, or stuck heating element relay.
7

Loud Noise or Vibration

Worn drum rollers, blower wheel issues, loose panels, or misaligned leveling legs.
8

Clothes Not Drying

Vent blockage, clogged lint filter, weak heating, or a faulty moisture sensor prevents proper drying.
9

Burning or Musty Smells

Lint near the heater, worn belt rubbing, or buildup on the heating element can cause smells.
10

Dryer Won’t Stop Running

Faulty cycling thermostat, defective timer, stuck relay, or moisture sensor failure.

Book Your Dryer Repair Today

Edmonton · Calgary · Red Deer & Nearby Areas

10 Common Cooktop Problems We Repair

Gas, electric, or induction – here are the most common issues we see during a Cooktop Repair Service.

1
Burner Not Heating Properly
Blocked burner ports, dirty electrodes, faulty igniters or elements can all cause weak or inconsistent heat.
2
One or More Burners Won’t Light
Common causes include bad ignition switches, loose wiring, failed spark modules, or faulty flame sensors.
3
Uneven Heat Distribution
Off-center burner caps, partially blocked ports, or damaged elements can create hot and cold spots in your pan.
4
Flame Too High or Too Low
Incorrect air–gas mix, misadjusted air shutters, or gas pressure issues can cause unstable or unsafe flames.
5
Power On but No Heat
For electric or induction units, failed elements, surface boards, or sensors may stop burners from heating.
6
No Power at All
Tripped breakers, loose connections, damaged power cords, or internal control failures can shut the cooktop down.
7
Burners Won’t Stay Lit
Weak or dirty flame sensors, faulty thermocouples, or poor gas flow can cause burners to shut off shortly after ignition.
8
Excessive Smoke While Cooking
Spills, grease buildup, or blocked ports can cause smoke and odours – especially on gas burners.
9
Not Reaching Set Temperature
Faulty temperature sensors, failing elements, or incorrect calibration can stop the cooktop from delivering full heat.
10
Unpleasant or Gas Odours
Spills, grease, or (on gas models) possible leaks or incomplete combustion—these should be inspected promptly for safety.

If you smell gas, see unstable flames, or breakers keep tripping, stop using the cooktop and book service.
Book Your Cooktop Repair Today

Edmonton · Calgary · Red Deer & Nearby Areas

10 Common Dishwasher Problems We Repair

Here are the top issues our certified technicians fix during a Dishwasher Repair Service.

1
Faulty Door Latch
A weak, damaged, or misaligned latch prevents the dishwasher from starting or sealing properly.
2
Leaking Water
Loose door seals, cracked hoses, damaged sump assembly, or failing water inlet valves are common leak causes.
3
Noisy Operation
Grinding, humming, or buzzing may indicate circulation pump wear, debris in impellers, or failing wash motors.
4
Not Cleaning Dishes
Blocked spray arms, dirty filters, weak water pressure, or faulty wash motors reduce cleaning performance.
5
Not Draining Properly
Clogged drain hoses, blocked filters, jammed drain pumps, or check valve issues can leave water at the bottom.
6
Unpleasant Odors
Food debris, grease buildup, or slow drainage can cause odors—cleaning and proper maintenance resolve this.
7
Not Filling with Water
Faulty inlet valves, clogged screens, low water pressure, or float switch issues prevent proper filling.
8
Poor Drying
A failing heating element, faulty thermostat, or broken vent fan can lead to wet or cloudy dishes.
9
Maintenance-Related Failures
Worn seals, dirty filters, loose hoses, and unmaintained spray arms can cause performance problems over time.
10
Detergent Buildup or Oversudsing
Using too much detergent, or the wrong type, can clog the system and create excessive suds.

Book Your Dishwasher Repair Today

Edmonton · Calgary · Red Deer & Nearby Areas

10 Common Microwave Problems We Repair

These are the most frequent issues our technicians solve during a Microwave Repair Service.

1
Faulty Door Switch
A broken or misaligned door switch stops the microwave from running for safety and usually needs replacement.
2
Blown Fuses or Tripped Breakers
Power surges or internal shorts can blow fuses or trip breakers, leaving the microwave completely dead.
3
Poor Power Supply
A weak outlet, loose plug, or unstable voltage can cause flickering displays, random shutoffs, or no operation.
4
Failed Magnetron
If the magnetron fails, the unit may run but food will not heat properly.
5
Incorrect Timer or Control Settings
A faulty touchpad or control board can cause wrong run times, random stopping, or unresponsive buttons.
6
Excessive Arcing or Sparking
Food splatter, metal objects, or damaged waveguide/cover can cause arcing—cleaning and inspection are important.
7
Faulty Temperature / Safety Controls
Defective thermostats or sensors may shut the unit down too soon or allow internal overheating.
8
Broken Interior Light
Burned-out bulbs or wiring faults require safe disassembly and correct replacement.
9
Electromagnetic Interference
Nearby devices or poor grounding can interfere with controls, displays, or Wi-Fi enabled models.
10
Poor Ventilation / Overheating
Blocked vents, tight cabinets, or grease buildup cause overheating and shorten component life.

Book Your Microwave Repair Today

Edmonton · Calgary · Red Deer & Nearby Areas

10 Common Stove Problems We Repair

Here are the issues our certified technicians most often fix during a Stove Repair Service.

1

Faulty Igniter

When the igniter is weak or dead, burners fail to light or take too long to ignite—replacement resolves the issue.
2

Clogged Burner Orifice

Grease, debris, or food spills block gas flow; cleaning the orifice restores even flame performance.
3

Poor Gas Flow

Gas supply issues, regulator failure, or valve restrictions require a trained gas-licensed technician.
4

Broken Heating Element

Electric ranges may stop heating due to cracked or burnt-out elements—replacement restores performance.
5

Defective Thermostat

A faulty thermostat causes inaccurate temperatures, uneven cooking, or overheating issues.
6

Loose or Broken Wiring

Electrical faults can prevent burners or the oven from heating and should be handled by professionals only.
7

Grease & Debris Buildup

Heavy grease inside the oven cavity affects temperature accuracy and can create smoke or fire hazards.
8

Worn or Damaged Door Gasket

A weak seal lets heat escape, leading to long cook times and uneven baking—replacement is recommended.
9

Faulty Temperature Control Knobs

Broken or inaccurate dials affect burner output; internal valve or switch replacement may be needed.
10

Control Board or Display Failure

Error codes, dead displays, or unresponsive buttons often point to a failing control board—diagnosis is required before ordering parts.

Book Your Stove Repair Today

Edmonton · Calgary · Red Deer & Nearby Areas

10 Common Oven Problems We Repair

From gas safety issues to temperature problems, here are the most common faults we see during an Oven Repair Service.

1

Dirty or Neglected Oven Interior

Heavy grease and carbon buildup can affect performance and create smoke. Technicians focus on repair; for heavy cleaning, follow the manufacturer’s instructions or use a professional cleaning service.
2

Door Not Sealing Properly

A misaligned door, worn hinges, or damaged gasket lets heat escape, causing long cook times and uneven baking.
3

Gas Smell or Suspected Leak (Gas Ovens)

If you smell gas, shut the oven off, ventilate the area, and contact a gas-licensed professional immediately—do not attempt DIY repairs.
4

Failed Heating Elements

Bake or broil elements that are cracked, blistered, or open-circuit will prevent the oven from heating or browning correctly.
5

Preheating & Temperature Problems

Faulty sensors, damaged elements, or miscalibrated thermostats cause slow preheat, temperature swings, and inconsistent baking results.
6

Clock & Timer Malfunctions

Broken clocks, timers, or control panels can affect delayed start, timed baking, and shutoff functions.
7

Damaged or Loose Wiring

Burned connectors or loose wires can cause intermittent heating or complete power failure and should be handled by a professional.
8

Igniter, Valves & Switch Issues (Ranges)

Weak igniters, stuck gas valves, or faulty switches can prevent the oven from lighting or maintaining flame in gas ranges.
9

Broiler Not Working Properly

Faulty broil elements, gas valves, or control faults lead to poor browning or no broil function at all.
10

Worn Racks & Interior Hardware

Warped racks, worn supports, or damaged guides can make it difficult to position pans safely and evenly inside the oven.

Book Your Oven Repair Today

pressure gauge for refrigerator repair by advance appliance ltd

Edmonton · Calgary · Red Deer & Nearby Areas

10 Common Refrigerator Problems We Repair

These are the most frequent issues our technicians diagnose during a Refrigerator Repair Service.

1

Dirty Condenser Coils

Dusty or greasy coils cause overheating and poor cooling—cleaning every 6–12 months improves efficiency.
2

Blocked Air Vents

Food packages or ice buildup blocking vents disrupt airflow and lead to warm fridge temperatures.
3

Incorrect Thermostat Settings

Misadjusted or faulty thermostats can cause freezing, warming, or inconsistent cooling.
4

Overloaded Freezer

Overpacked freezers restrict airflow and cause both freezer and refrigerator sections to warm up.
5

Worn Door Seals / Gaskets

Cracked, loose, or warped gaskets allow cold air to escape, forcing the fridge to work harder and cool poorly.
6

Blocked Defrost Drain

Frozen or clogged drains cause water leaks, ice sheets, and restricted airflow inside the refrigerator.
7

Failing Evaporator or Condenser Fan

Weak or dead fans prevent proper air circulation, causing warm spots and inconsistent cooling.
8

Motor or Compressor Problems

A weak motor or failing compressor leads to long run times, poor cooling, or complete no-cool situations.
9

Ice Build-Up

Excess frost blocks airflow and reduces cooling performance—often caused by sensor, heater, or drain issues.
10

Compressor Failure

A failing compressor prevents the fridge from cooling at all—requires professional diagnosis before replacement.

Book Your Refrigerator Repair Today

Range Hood and Cooktop Repair - Advance Appliance Ltd

Edmonton · Calgary · Red Deer & Nearby Areas

10 Common Range Hood Problems We Repair

These are the most frequent issues we diagnose during a Range Hood Repair Service.

1

Clogged Grease Filters

Dirty filters reduce airflow and cause strong cooking odors—cleaning or replacing restores performance.
2

Weak or Slow Fan

Obstructions, failing motors, or loose connections can prevent the blower from reaching full speed.
3

Blocked Exhaust Vent

Indoor or outdoor vent blockages restrict airflow, causing smoke buildup and poor ventilation.
4

Lights Not Working

Burned bulbs, faulty wiring, or damaged sockets can lead to lighting failure under the hood.
5

Loud or Vibrating Motor

Unbalanced blowers, worn bearings, or loose screws often cause grinding, humming, or rattling sounds.
6

Grease Build-Up on Surrounding Walls

Poor ventilation or clogged filters cause excess grease to escape—clean surfaces and restore airflow.
7

Loose or Improper Duct Connections

Poorly sealed ducts leak air, reduce suction, and create excess noise—tightening and sealing resolves it.
8

Motor Running but Fan Not Spinning

Obstructions, slipping fan wheels, or a damaged blower assembly can prevent blade rotation.
9

Loose Screws or Internal Components

Vibrations can loosen internal hardware—tightening ensures safe, quiet operation.
10

Vent Cover Not Opening or Closing

Broken hinges, stuck dampers, or poor lubrication prevent proper airflow control—repairs restore full function.

Book Your Range Hood Repair Today

Freezer evaporator for ice maker and refrigerator repair by Advance Appliance Ltd

Edmonton · Calgary · Red Deer & Nearby Areas

10 Common Ice Maker Problems We Repair

Our Appliance Repair team regularly diagnoses and fixes these issues during an Ice Maker Repair Service.

1

Poor Water Flow or Low Pressure

Weak water supply, restricted valves, or faulty filter heads reduce fill levels and slow ice production.
2

Clogged Water Line

Mineral deposits, debris, or old filters can partially block the line—filters should typically be replaced every 6 months.
3

Overfilled or Underfilled Ice Molds

Incorrect fill levels may be due to faulty water valve control or internal adjustments—best verified by a technician before parts are replaced.
4

Freezer Temperature Too Warm or Too Cold

Incorrect settings, bad sensors, or sealed system issues affect cube size and production speed and should be professionally checked.
5

Shutoff Arm or Sensor Not Working

A stuck arm or faulty level sensor may not stop production, causing jams or overflowing bins.
6

Ice Maker Motor or Drive Issues

Worn gears, broken couplers, or failed motors prevent the ejector from turning—diagnosis by a technician is recommended before parts replacement.
7

Leaks from Valves, Hoses, or Seals

Drips behind or under the fridge may come from loose fittings, cracked lines, or faulty valves and should be professionally inspected.
8

Clogged or Frozen Drainage

Blocked drains can cause water to pool around the ice maker area or freeze into sheets—underlying causes should be confirmed before repairs.
9

Excess Frost or Ice Buildup

Insufficient defrost, warm air leaks, or airflow issues can cause heavy frost, affecting both ice quality and production.
10

Control Board or Sensor Failures

Faulty boards or sensors can cause random stops, no production, or incorrect temperatures—these should be tested by a professional before ordering parts.

Book Your Ice Maker Repair Today

Advance Appliance Ltd. — Repair Information Disclaimer

The information provided on the Advance Appliance Ltd. website is for general informational purposes only and should not be considered technical or professional repair advice. We strongly recommend contacting a licensed appliance repair technician for accurate diagnosis and repair.

While every effort is made to keep our troubleshooting guides and repair information accurate and up to date, we cannot guarantee that all details are complete, error-free, or suitable for DIY use. Appliance systems vary by brand, model, and condition, and improper handling can cause damage or safety hazards.

Advance Appliance Ltd. is not responsible for any injuries, damages, or losses that may occur as a result of using information from this website. This disclaimer applies only to the content on our website and does not extend to external repair resources or third-party sites.

Thank you for using our website and for choosing Advance Appliance Ltd. for your appliance repair needs.